1. COURSE: This course provides the required classroom and practical training for operating vehicles equipped with air brake systems under provincial regulations.
2. ATTENDANCE: Full attendance is mandatory. Students who arrive more than five minutes late may be refused entry. Missed sessions must be rescheduled (fees may apply). All required hours must be completed.
3. IDENTIFICATION: A valid, unexpired, non-suspended driver’s licence must be presented.
4. CONDUCT & SAFETY: Students must follow all instructor directions. Unsafe conduct, misuse of equipment, or disrespectful behavior will result in removal without refund. Alcohol, drugs, or impairment are strictly prohibited.
5. PAYMENT: Full payment is required before the course starts unless otherwise approved. Fees are non-refundable once training begins.
6. EXAMINATIONS: Students must pass the in-class test and practical air brake inspection test. Retesting may require additional training and fees. ICBC passing standards apply.
7. CERTIFICATION: Successful completion provides proof of training only. The final endorsement is issued solely by ICBC, the provincial licensing authority.
IMPORTANT DISCLAIMER: Successful completion of this course does NOT guarantee air brake endorsement or issuance of a driver’s licence. If money is owed to ICBC, a hold may be placed on the licence until paid. ICBC may retest at any time, deny or delay endorsement, and access all school training records. All licensing decisions are made solely by ICBC.
8. CANCELLATION: A minimum of 48 hours’ notice is required to reschedule. No-shows may forfeit fees. The school may reschedule due to low enrollment or unforeseen circumstances.
9. LIABILITY: The school is not responsible for lost or stolen items. Students participate at their own risk. The school is not liable for any injury or damage resulting from failure to follow safety rules or instructor directions during training.
STUDENT DECLARATION: I confirm that I have read, understood, and agree to the above policies and disclaimer.
Step 2: Take the multiple-choice air brake theory test at ICBC (25 questions; 80% is the passing grade).
Step 3: Complete a practical air brake test in one of the following ways:
As part of a Class 5 air brake endorsement course with Nanak Driving School Ltd.
As part of your Class 1 road test through ICBC.
As part of your Class 3 road test through ICBC.
Start here · Section 4 of 25
Air Brake Certification Notice
ATTENTION: STUDENTS COMPLETING AIR BRAKE CERTIFICATION
NANAK Driving School Ltd.
Disclaimer
5.11.1 A certificate does not guarantee that ICBC will issue a driver’s licence or air brake endorsement.
5.11.2 ICBC may require a certified trainee to be retested by a driving examiner.
5.11.3 ICBC will have access to trainees’ training and assessment records.
In plain language, if you owe ICBC money or have outstanding issues with ICBC, it may decline to issue you a licence or endorsement.
Safety & rules · Section 5 of 25
Driver Responsibility
DRIVER RESPONSIBILITY
Air brake system designers have done their best to provide safe and efficient vehicles.
Drivers are responsible for ensuring that all safety features built into their vehicles operate correctly. Heavy-truck accidents involving brake failure are often associated with neglect or human error rather than a failure of the air brake system itself.
The National Safety Code of Canada requires a daily pre-trip inspection and a signed inspection report to be carried in the vehicle. Among the most important pre-trip checks are the condition and adjustment of foundation brakes. When it comes to brake adjustment, “good enough” is never good enough.
The driver is fully responsible.
Safety & rules · Section 6 of 25
Violation Tickets & Fines
VIOLATION TICKET ADMINISTRATION AND FINES REGULATION
Section 6.02(2)
The fines are categorized based on the number of defective service brakes found during an inspection:
Individual Defective Brake: A $120 fine (Column 3A) is issued for each service brake not in effective working order.
Major Defective Brake Violation: An additional penalty results in a total fine of $520 (Column 3A) if 50% or more of the vehicle’s service brakes are not in effective working order.
Maximum Potential Fine: Operating a vehicle with defective brakes can lead to a fine of as much as $2,000 under the general penalty provisions of the Offence Act.
Introduction to air brakes and heavy vehicle braking 60
Air brake components 100
Other types of foundation brakes 15
Other air brake system components 15
Components review 30
Brake adjustment 60
(manual slack adjustment)
Air brake pre-trip inspection 60
Activity 20
Air brake review quiz 30
Pre-trip test at ICBC 15
Total course time 420 (7 hours)
Day 2 — Sunday
(4 hours of practical training and a 30-minute assessment)
Air Brake Practical Training and Certification
Introduction to yard safety
Location and purpose of air brake components
Discuss the types of components
Working principles (airflow paths)
Testing and inspection procedures
Adjustment and repair
En-route inspection and certification procedures
Safety & rules · Section 8 of 25
Heavy Truck Accidents in BC
HEAVY TRUCK ACCIDENTS IN BC
September 1, 1989 — Coquihalla Highway (southbound)
A 1987 Western Star tractor towing a loaded B-train lost braking control and gained speed over a distance of 14 kilometres. The engine was damaged by over-revving, and the truck eventually collided with the rear of a southbound station wagon.
One passenger in the station wagon and the truck driver were killed. Both bodies were incinerated in the resulting fire.
BRAKE CONDITION: The tractor was consumed by fire, so its brake condition could not be assessed.
Seven of the eight trailer brake drums were worn well beyond the manufacturer’s maximum allowable size. Three trailer brake chambers had bottomed out, and the other five had pushrod strokes of 2 1/8 inches or more.
October 27, 1989 — Kamloops, British Columbia
A 1980 Kenworth tractor towing a loaded semi-trailer lost braking control on a steep city street. After passing through two red traffic lights, the vehicle struck several passenger cars stopped at a traffic signal. Five people, including the truck driver, died in the crash and resulting fire.
BRAKE CONDITION: The steering-axle brakes were too badly damaged to assess their effectiveness.
The drive-axle brakes had been adjusted in the wrong direction, leaving them completely ineffective.
The trailer brake drums were worn well beyond the manufacturer’s maximum allowable diameter. Some drums measured more than 17 inches, over 1/2 inch larger than the standard 16 1/2-inch size.
Two trailer brake chambers had pushrod strokes of approximately 2 inches, while the other two were just within the legal maximum stroke.
The trailer brake linings were worn down to the rivet heads.
Note: This vehicle bore a current, valid inspection sticker from the Province of Alberta.
July 9, 1990 — Horseshoe Bay, West Vancouver, British Columbia
A 1984 Ford dump truck carrying asphalt lost braking control on the grade leading to the Horseshoe Bay ferry terminal.
The vehicle exceeded the manufacturer’s gross vehicle weight rating by 15%. After running through the toll gate, the truck struck the rear of a parked van, killing two people and injuring seven.
BRAKE CONDITION: The steering-axle brakes (wedge type) were missing vital parts of their self-adjusting mechanisms, leaving them out of adjustment and minimally effective.
Three drive-axle brake chambers bottomed out at an application pressure of 120 psi, while the fourth had a 2-inch pushrod stroke.
THE DRIVER WAS CHARGED AND CONVICTED OF CRIMINAL NEGLIGENCE
Note: This vehicle bore a current, valid inspection sticker from the Province of British Columbia.
SUMMARY: These three accidents caused nine deaths and numerous injuries. In the source account, neglect of brake adjustment and improper braking-system maintenance were identified as causes.
Safety & rules · Section 9 of 25
Heavy Truck Accidents in Washington
HEAVY TRUCK ACCIDENTS IN WASHINGTON
November 1989 — Gig Harbor, Washington
A 1978 Kenworth tandem truck loaded with firewood lost braking control on a grade of up to 14% in Gig Harbor. The road ended at a T-intersection at the bottom of the grade.
The driver attempted to downshift, but even at full governed engine speed, a lower gear could not be engaged.
The truck travelled downhill in neutral at high speed and entered a restaurant at the intersection.
A waitress was killed. The truck fell through the restaurant floor, and the building was destroyed. The driver sustained minor cuts and bruises.
BRAKE CONDITION: The steering-axle brakes were of the wedge type. Their self-adjusters had failed, leaving the brakes ineffective.
One drive-axle brake was cammed over (the shoes had worn to the point that the S-cam rotated too far for the shoe roller to return to its normal position). The remaining three pushrod strokes measured 2 inches, 2 1/8 inches and 2 1/4 inches.
The driver stated that he always had to use the gears to slow down because the brakes alone were very weak.
This accident resulted in lawsuits seeking several million dollars. Some were settled out of court, and the settlement amounts were not disclosed.
Truck Driver Faces Eight Counts of Criminal Negligence Following 2016 Coquihalla Crash
Coquihalla crash
Trial of Roy McCormack begins in B.C. Supreme Court in Chilliwack
The trial in B.C. Supreme Court in Chilliwack raised the question of whether a commercial truck driver had properly checked his brakes before travelling on the Coquihalla Highway in 2016.
Roy D. McCormack faced eight counts of criminal negligence causing bodily harm and one count of dangerous operation of a motor vehicle following a multi-vehicle collision on Highway 5 (Coquihalla Highway) on August 5, 2016.
The five-day trial began in Courtroom 201 before Justice Peter Edelman. The court clerk read the charges aloud to McCormack, who attended in person.
He pleaded not guilty to all eight criminal-negligence charges and the dangerous-operation charge.
Each of the eight criminal-negligence charges related to an individual injured in the collision near Box Canyon on the Coquihalla.
RELATED: 30 years later: Stories from the Coquihalla
Brake Issue Reported in Tractor-Trailer Crash on Highway 3 Near Princeton (June 6, 2025)
The driver sustained minor injuries, and no criminal activity was suspected.
RCMP investigated a single-vehicle incident involving a semi-truck on June 6.
On June 6, a tractor-trailer overturned and struck highway barriers after overtaking another truck across a double solid line. The collision occurred eastbound on Highway 3 near the Mine Hill area, outside Princeton. RCMP reported that a brake issue contributed to the crash.
"The driver reported his braking system had failed, and in order to avoid another vehicle, attempted a sharp turn, in which he couldn't straighten out," Cpl. James Grandy said. "This resulted in the semi overturning."
Const. Kelly Brett added that the mechanical failure caused the vehicle to gain speed going downhill and the driver had limited options to immobilize the vehicle.
"He passed another vehicle, also eastbound, to prevent a collision, but his vehicle rolled when he attempted to negotiate a sharp turn ahead," Brett said. The driver sustained minor injuries.
No other vehicles were involved and no criminality is suspected. The matter remains under investigation.
Air brake fundamentals · Section 10 of 25
Air Brake Components & Functions
Air Brake System Components and Functions
COMPONENT
FUNCTION
Air Compressor
Compresses air for the brake system. Driven by the engine, it draws in filtered air and delivers it to the reservoirs.
Air Intake Filter
Filters incoming air before it enters the compressor to prevent dirt and debris from entering the system.
Air Dryer
Removes moisture and oil vapour from compressed air to prevent freezing and corrosion; often includes a purge valve.
Alcohol Evaporator (optional)
Adds alcohol vapour to the air system to prevent ice formation in cold weather; connected to the inlet side of the compressor.
Alcohol Injectors
Installed in the compressor discharge line between the compressor and the supply reservoir to prevent freezing.
Air Governor
Controls minimum and maximum air pressure in the system. Max pressure: 105–135 psi; cut‑in about 20 psi below cut‑out.
Air Compressor Unloader Mechanism
Allows compressor to idle when cut‑out pressure is reached to prevent over‑pressurization.
Reservoirs (Tanks)
Store compressed air for the system: Supply/Wet Tank, Primary Tank, Secondary Tank.
Automatic Drain Valves / Spitter Valves
Automatically expel moisture and contaminants when reservoir pressure drops slightly; some include heaters.
Drain Valves / Drain Cocks
Located at the bottom of reservoirs to allow manual removal of water and oil.
One‑Way Check Valve
Allows air to flow in one direction only, preventing backflow and isolating reservoirs.
Two‑Way Check Valve
Directs air from either of two sources to one delivery line. (The higher pressure is directed to the delivery port.)
Pressure Protection Valve
Maintains minimum pressure before supplying air to non‑essential accessories (60–90 psi).
Safety Valve
Protects the system from over‑pressurizing if the governor fails; usually opens around 150 psi. (It is threaded directly into the supply reservoir.)
Foot Valve / Treadle Valve
Controls air flow from reservoirs to brake chambers when the brake pedal is pressed.
Dual Foot Valve
Combines two foot valves in one unit (primary and secondary circuits) for redundancy.
Brake Chambers
Convert air pressure into pushrod force to apply brakes. Service brake chamber sizes range from T-6 to T-36. Pushrod stroke on a standard chamber: 2.5 inches.
Spring Brake Chambers
Provide parking brake force and emergency braking when air pressure is lost.
Spring Brake Modulator Valve
Allows controlled spring brake application if a primary air system fails.
Slack Adjusters
Transfer pushrod force to the S‑camshaft and allow brake adjustment.
Clevis & Yoke
Connect brake chamber pushrod to the slack adjuster.
Brake Linings
Provide friction between brake lining and drum to stop the wheels.
S‑Cam
Rotates to push brake shoes outward against the drum.
Wedge‑Type Brake
Uses wedge action to apply brake shoes; mostly self‑adjusting.
Quick Release Valve
Releases air quickly from brake chambers to reduce brake release time.
Relay Valve
Speeds up brake application and release, especially for trailer brakes.
Relay Emergency Valve
In trailers, applies brakes quickly in emergencies and controls emergency air from the trailer reservoir. (Motor vehicle safety standards require these systems to remain applied for a minimum of 15 minutes.)
Hand Valve / Spike
Allows driver to apply trailer brakes independently from tractor brakes.
Park Control Valve
Applies and releases parking brakes (usually with a yellow knob).
Tractor Protection Valve
Protects the tractor air supply if the trailer air lines disconnect.
Trailer Supply Valve
Controls air supply to trailer tanks; usually with a red octagonal knob.
Tractor Protection System
Prevents total air loss from the tractor if the trailer disconnects.
Caging Bolt
Mechanically releases spring brakes when there is no air pressure.
Dual Control Valve Emergency release valve (California brake valve)
Allows the use of an emergency-release tank to temporarily release spring brakes.
Manual Front-Wheel Limiting System
Reduces front-wheel braking force by about 50% on slippery roads.
Automatic Front-Wheel Limiting Valve
Automatically reduces front brake pressure at low air pressures. At application pressures above 40 psi, the percentage gradually rises until it reaches 60 psi, a pressure that may be used during an emergency stop.
Low Pressure Warning Device
Alerts driver when air pressure drops below 60 psi.
Stop Light Switch
Air‑operated switch that activates brake lights when brakes are applied.
ABS Electronic Control Unit (ECU)
Monitors wheel speed sensors and controls ABS modulator valves.
ABS Modulator Valves
Rapidly apply and release brake pressure to prevent wheel lock‑up.
Wheel Speed Sensors
Detect wheel rotation speed for ABS.
Bobtail Proportioning System
Reduces rear brake application by about 75% when the tractor operates without a trailer.
DD‑3™ & SD‑3™ Safety Actuators
Used mostly in buses; a mechanical lock keeps the brakes applied until they are released by air.
Air Pressure Gauges
Indicate system pressure in primary and secondary circuits.
Application Pressure Gauge
Shows air pressure delivered to brake chambers during braking.
Glad Hands (Service & Emergency)
Coupling connectors between tractor and trailer air lines (blue service, red emergency).
Air Lines (Service & Emergency)
Flexible hoses carrying compressed air between tractor and trailer.
Service Line
Delivers application air from the tractor foot valve to the trailer relay valve.
Emergency Line
Supplies air to the trailer tanks and controls emergency brake application.
Pressure Regulator Valve
Regulates pressure delivered to auxiliary systems such as suspension or air horns.
Load Sensing Valve
Adjusts brake force based on vehicle load to prevent wheel lockup.
Spring Brake Chamber Locking Mechanism
Locks spring brakes mechanically to prevent vehicle movement during maintenance.
Brake Drum
Rotating component attached to the wheel hub that the brake shoes press against.
Brake Shoe
Curved metal component that holds the brake lining that contacts the drum.
Emergency Brake Valve
Automatically applies trailer brakes if the trailer air-supply line breaks or disconnects.
Trailer spring brake valve
A critical air brake component that controls the application and release of the trailer's spring (parking and emergency) brakes. It ensures that the trailer remains stationary when parked and provides automatic braking if the air supply is suddenly lost, such as during a breakaway
Feature “Spring Brake Priority” (SBP)
Releases parking brakes as quickly as possible. It fills the spring chambers first, then the reservoirs. The trailer can roll before there is enough air to operate the service brakes.
Service Priority
Ensures that service brakes work before the trailer moves. It fills the reservoirs first, then releases the spring brakes. This ensures full braking capability before the trailer can move.
Long stroke brake chambers
Identified by their square-shaped inlet ports and/or trapezoid-shaped name tag on a clamp bolt. Pushrod stroke up to 3 inches.
BASIC AIR BRAKE SYSTEM
Air brake fundamentals · Section 11 of 25
Stopping Distance & Time
STOPPING DISTANCE AND STOPPING TIME
👀 SEE — Identify a hazard. 🧠 THINK — Decide to stop. 🦶 ACT — Move your foot to the brake pedal and stop.
⏱️ BRAKE LAG TIME → The interval between applying the brake pedal and the brakes beginning to operate.
At 50 km/h, your vehicle travels about 45 feet (13.89 metres) each second.
At 50 km/h, ¾ of a second represents approximately 34 feet.
At 50 km/h, 4/10 of a second represents approximately 18 feet.
The vehicle has travelled 86 feet, and the brake linings are only just making contact with the brake drums.
Braking distance is not fixed; it changes with the conditions.
🚗 Speed of the vehicle ⚖️ Vehicle weight / load 🛞 Brake condition
🛣️ Road surface 🛞 Tire condition
⛰️ Road grade (hill) 🌧️ Weather conditions
Braking distance is the distance a vehicle travels from the point at which its brake linings contact the drums until it comes to a stop.
Air brake fundamentals · Section 12 of 25
Stopping Power
STOPPING POWER REQUIRED TO STOP A VEHICLE
How Speed and Weight Affect Stopping Power
Speed and weight affect the stopping power required to stop a vehicle and the distance it travels before stopping. More stopping power is needed as the speed and/or weight of the vehicle increases:
• 2 X vehicle speed requires 4 X the stopping power
• 2 X vehicle weight requires 2 X the stopping power
• 2 X vehicle speed and 2 X vehicle weight requires 8 X the stopping power
Air brake fundamentals · Section 13 of 25
Following Distance
FOLLOWING DISTANCE
If conditions are less than ideal, increase your following distance. Driving conditions are affected by:
Road conditions
Vehicle conditions
Your physical and mental condition
Traffic conditions
Lighting conditions
Weather conditions.
It is very important to maintain a safe distance behind other vehicles. Drivers of buses, trucks and other large vehicles should allow at least one second for every 3 m (10 ft) of overall vehicle length, with a minimum of
five seconds behind the vehicle ahead under ideal driving conditions. When conditions are less than ideal, increase your following distance. To measure it, watch the vehicle ahead pass a stationary object (such as a utility pole) and count:
• One thousand and one
• One thousand and two
• One thousand and three
• One thousand and four
• One thousand and five
Stop counting when your front bumper reaches the same object. The number of seconds gives you your following interval. If you pass the object before finishing your count, you are following too closely.
Slow down and increase your following distance.
Repeat the count until you are at least five seconds behind the vehicle ahead.
Practical training · Section 14 of 25
Practical Yard Safety
PRACTICAL YARD TRAINING
Yard Safety During Practical Training
Even when the training vehicle is stationary, hazards remain, including moving vehicles, uneven ground and mechanical risks.
1. Prepare Before You Begin
Wear PPE: high-visibility vest, steel-toe boots, gloves if needed
Park in a safe inspection area away from traffic flow if possible
Apply the parking brake and chock wheels if on a slope
Turn off the engine unless it’s required for a specific check
2. Be Aware of Your Surroundings
Watch for other trucks, yard tractors, forklifts, and pedestrians
Avoid standing in blind spots of other vehicles
If you drop tools or paperwork, check surroundings before picking them up
3. Engine Compartment Safety
Only open the hood when the vehicle is fully stopped and secure
Be cautious of hot components (radiator, exhaust)
Keep clear of moving belts, fans, and pulleys if the engine is running
4. Under-Vehicle and Wheel-Area Safety
Never crawl fully under a vehicle unless it’s properly supported
Use caution when inspecting brake components — watch for sharp edges and pinch points
Avoid standing directly in front of wheels while another person is in the cab
5. Air Brake System Safety
When checking for leaks, stay clear of moving brake parts
Do not put your face or hands close to high-pressure fittings
Follow proper build-up and cut-out procedures to prevent unexpected movement
6. Communication
If working with another driver, agree on signals before moving the vehicle
Make sure the driver in the cab knows that you are inspecting the vehicle before starting the
engine
7. General Safe Practices
Keep inspection tools and documents organized and off the ground to avoid tripping
Maintain three points of contact when climbing in and out of the cab
Report any unsafe conditions in the yard immediately
Air brake fundamentals · Section 15 of 25
Component Locations & Purposes
Air Brake System – Complete Detailed Reference
1. Engine Compartment
Component
Location
Purpose
Air Compressor
Mounted on the engine, gear-driven (sometimes belt-driven on buses)
Supplies compressed air to the system
Governor
Attached to compressor or firewall
Controls compressor cut-in (≈80–85 psi) and cut-out (≈105–135 psi)
Air Dryer
Between the compressor and the first tank
Removes water, oil, and contaminants from compressed air
Air Filter
Usually mounted in a housing connected to intake manifold
Cleans incoming air before it enters the engine and compressor
Engine Coolant System
Radiator, hoses, and coolant reservoir in front of engine
Maintains engine and compressor temperature to prevent overheating
Engine Oil System
Oil reservoir (sump), dipstick, and filler cap on engine block
Lubricates engine and compressor, reducing wear and preventing overheating
Belts & Pulleys
Front of engine
Drive accessories such as alternator, fan, or belt-driven compressor
2. Chassis / Frame Area
Component
Location
Purpose
Primary & Secondary Reservoirs (Air Tanks)
Along the frame rails
Store compressed air for each system (front/rear brakes)
Supply (Wet) Tank
Closest to the compressor
First stage storage; collects most moisture and oil
Check Valves
Between tanks
Allow air flow in one direction only and prevent backflow
Air Lines
Throughout frame and underbody
Carry compressed air at high pressure between components
Relay Valve
Near the rear axles
Reduces delay by releasing air from nearby tank directly to brakes
Quick Release Valve
Near the brake chambers
Allows rapid air exhaust for quick brake release
ABS Modulators
Near wheels or frame cross members
Modulate air pressure to prevent wheel lock-up
3. Wheel End (Foundation brake components)
Component
Location
Purpose
Brake Chamber
Behind each wheel, bolted to the axle
Converts air pressure to pushrod force
Pushrod
From chamber to slack adjuster
Transfers force to slack adjuster
Clevis & Clevis Pin
At the pushrod end
Mechanical connection point
Slack Adjuster
On camshaft splines
Rotates S-cam to apply brakes
S-Cam
Inside brake spider housing
Spreads brake shoes apart
Brake Shoes & Linings
Inside the brake drum
Create friction against drum to slow wheel
Brake Drum
Attached to wheel hub
Rotating surface for shoes to press against
4. Cab Area
Component
Location
Purpose
Tachometer
Dashboard
Measures engine RPM (Revolutions Per Minute)
Air Pressure Gauges
Dashboard
Show primary and secondary system pressures
Application Pressure Gauge
Dashboard
Shows air pressure applied to brakes
Low Air Pressure Warning (Light/Buzzer)
Dashboard
Activates before 60 psi
Parking Brake Control (Yellow Knob)
Dashboard
Applies the tractor spring brakes
Trailer Air Supply (Red Knob)
Dashboard
Controls the trailer emergency brakes
Trailer Hand Valve
Dashboard or steering column
Applies trailer service brakes only
ABS Warning Light
Dashboard
Alerts the driver to an ABS fault
5. Rear of Tractor
Component
Location
Purpose
Tractor Protection Valve
At the rear frame crossmember
Prevents air loss from tractor if trailer disconnects
Glad-hands
Rear air connections
Connects tractor and trailer service and supply lines
Electrical Connector (7-way plug)
Next to glad-hands
Provides electrical signals to trailer lights and ABS
Air brake fundamentals · Section 16 of 25
Types of Key Components
2. Types of Key Components
Air Compressor – Gear-driven (most trucks) or belt-driven (some buses).
Brake Chambers: Service Chambers — A single diaphragm provides service braking only.
Spring Brake Chambers – Double unit; service brake + parking/emergency spring.
Regular Stroke Brake Chamber : Standard brake chamber with typical pushrod travel length (usually around 1.5 to 2 inches). Suitable for most applications where normal stroke is sufficient for effective brake application.
Long Stroke Brake Chamber : Designed with extended pushrod travel (often 3 inches or more) to provide greater leverage and force. Used when additional stroke is needed due to worn brake components or specific vehicle requirements to ensure full brake application
Slack Adjusters:
Manual – Require regular manual adjustment. o Automatic (ASA) – Self-adjust within limits.
3. Working Principle (Air Flow Path)
Air compressor draws in filtered air → compresses it → sends to air dryer → tanks
Governor monitors system pressure:
At cut-out pressure (≈ 105-135 psi), it signals the compressor to unload (stop pumping air).
At cut-in pressure (≈ -20 psi or 80-85 psi), it signals the compressor to load (start pumping again).
Air dryer removes moisture/oil → sends to supply (wet) tank. ( A Desiccant is a drying agent used to absorb or adsorb moisture from the air )
One way check valves direct air to primary & secondary reservoirs.
Brake pedal (foot valve) pressed → sends air to service brake circuits.
Relay valve speeds brake application to rear wheels.
o Linings press against drum → friction slows wheel.
Tires transfer braking force to road.
Pedal released → quick release valve vents air → springs retract shoes.
Practical training · Section 17 of 25
Testing & Inspection Procedures
4. Testing & Inspection Procedures
A. Brake Adjustment Check
Make sure you have the proper equipment to check the brakes. You’ll need:
A flashlight to inspect components
Chalk or other marker, and a ruler or other marking device, to check pushrod free stroke
A tool to pry on the air brake chamber pushrod to check for free stroke
A wrench to adjust manual slack adjusters.
You should also wear sturdy clothing, a hard hat and eye protection.
If the red marking on the pushrod (at the chamber face) is visible, it indicates that the brake is dangerously out of adjustment and it needs immediate attention
How do you correctly measure brake chamber stroke?
You will also need another person to apply the service brakes. The procedure is as follows:
APPLIED STROKE MEASUREMENT METHOD: Most manufacturers of automatic slack adjusters specify that pushrod stroke be checked by making a 90 to 100 p.s.i. (620 to 690 kPa) application. If you have no application pressure gauge, turn the engine off and pump the reservoir pressure down to between 90 and 100 p.s.i. (620 to 690 kPa) — then make a full application.
Step One – Ensure the vehicle is in a safe location and make sure the wheels are properly chocked to prevent rolling. Release the spring brakes. Confirm your dash gauge indicates 90 to 100 psi (620 to 690 kPa) supply pressure in the air brake system reservoirs. Then, shut off the engine. Note: Supply reservoir pressure exceeding 110 psi (758 kPa) will result in incorrect pushrod stroke assessments.
Step Two – Visit each brake and confirm it is in the normal released position with nothing wrong or out of place. Mark each pushrod to establish a reference starting location. This should be level with where the pushrod exits the brake chamber or the chamber mounting bracket. Note where the pushrod mark started and where it ends up, then measure the difference in the next step. See Figure 1.
Step Three – Have the other person press and hold the service brakes (pushing the brake pedal all the way down until it stops) while you measure and record the distance each pushrod mark moved (or “stroked”).
Note: It is normal for pressure to drop slightly as brakes are applied. If multiple brake applications cause the pressure to drop below 90 psi (620 kPa), pause the procedure to rebuild reservoir pressure to 90 to 100 psi (620 to 690 kPa), then resume with the engine off.
Step Four – Compare your recorded pushrod stroke values with the stroke limits in the regulation for your brake chambers. See Table 1. If any chamber stroke measurement is near, at or beyond the prescribed regulatory stroke limit for your chamber type or size, the foundation brake, brake chamber, SABA, drum and wheel-end need to be inspected in more detail and serviced as soon as possible. If any pushrod stroke measurement exceeds the prescribed stroke limit, a violation exists. Any vehicle or combination of vehicles with 20% or more of the wheel ends containing brake violations is out of service per the CVSA North American Standard Out-of-Service Criteria.
What about free-stroke and slack?
Measuring chamber free-stroke or chamber pushrod slack, which is the distance you can pull the brake chamber pushrod by hand using a bar or lever without applying air pressure to the chamber, does not confirm a brake is working properly under all conditions. Chamber free-stroke longer than 3/4” may indicate a more serious issue. However, shorter free-stroke does not confirm proper brake chamber stroke.
1. Checking automatic slack adjusters
Pushrod strokes with automatic slack adjusters are usually slightly longer than with well-adjusted manual slack adjusters. With a typical Type 30 clamp type air chamber and an automatic slack adjuster,
The Brakes Need Repair If Pushrod Measurements Are Outside the Specified Limits:
PRY METHOD OF FREE-STROKE MEASUREMENT: Less than 1/2 inch or more than ¾ inch (20 mm).
APPLIED-STROKE METHOD: Less than 1½ inches or more than 2 inches (50 mm) under brake application.
2. Checking manual slack adjuster
With a typical Type 30 clamp-type air chamber, you must adjust the brakes if pushrod travel is:
• Less than ½ inch or more than ¾ inch (20 mm) using the pry method of free-stroke
measurement; or
Less than 1½ inches or more than 1¾ inches (45 mm) using the applied-stroke measurement method.
Use this table to determine the stroke limit in the regulation corresponding to the chamber size and type (standard or long-stroke design) for each brake on the vehicle.
B. Brake Lining Thickness
Drum brakes:
Brake linings must not be less than 1/4 inch (6.4 mm) thick.
On the steering axle, the minimum thickness is 3/16 inch (4.8 mm).
Disc brakes:
Brake pads must not be less than 1/8 inch (3.2 mm) thick.
(Compressor) Air Pressure Build-Up
From 50 to 90 psi in no more than 3 minutes (1,000–1,200 rpm).
D. Governor Test
Cut-Out Test — Build air pressure and note the gauge reading when the compressor stops pumping (approximately 105–135 psi).
Cut-In Test — Pump the brakes to lower pressure and note the reading when the compressor resumes pumping (approximately 80–85 psi).
Differential Check — The difference between cut-in and cut-out should be approximately 20–25 psi.
If outside specification, the governor should be inspected, adjusted or replaced as required.
E. Air Leakage Test
Maximum permitted air loss (turn the engine off so that you can listen for air leaks):
Visual Inspection — Regularly check all air lines for cracks, abrasion, leaks and proper routing.
Leak Detection — Apply soapy water or leak-detection spray to fittings and lines while the system is pressurized. Bubbles indicate leaks.
Practical training · Section 18 of 25
Adjustment & Repair
5. Adjustment & Repair
Safety Reminders
Never crawl under a vehicle with the brakes applied unless the spring brakes are caged and the wheels are blocked.
Test each brake during the pre-trip inspection.
Replace damaged hoses immediately.
Do not adjust automatic slack adjusters without first diagnosing the cause.
A. Manual Slack Adjuster
Park safely and chock the wheels.
Release the spring brakes.
Pull the slack adjuster and check that the direction of S-cam rotation matches the direction during brake application.
Turn the adjusting nut until it is tight, ensuring that the S-cam rotates in the same direction as during brake application.
Pull the slack adjuster to check that it is tight and that there is no pushrod travel.
Back off the adjusting nut by approximately 1/3 turn (about 20 minutes on a clock face).
Check that pushrod travel is between ½ and ¾ inch.
Make sure the locking collar is positioned over the adjusting nut.
Automatic Slack Adjuster
Normally self-adjusts during full brake application while moving.
Automatic slack adjusters must still be checked regularly to ensure correct adjustment.
If outside specifications, inspect for wear or defects before making an adjustment.
Brake Chamber Caging
For towing without air pressure, insert the caging bolt and tighten it to compress the spring.
Reservoir Draining
Drain daily unless automatic drains are installed (if equipped with ADIS, drain weekly).
Air Line Repair
Air Line Replacement: Replace damaged or worn air lines immediately. Use the correct type and size of hose or tubing.
Couplings and Fittings: Inspect for corrosion, cracks and proper tightness. Replace or tighten as needed.
Practical training · Section 19 of 25
Yard Pre-Trip Inspection Steps
Yard Pre-Trip Inspection Steps
AS YOU APPROACH THE TRUCK
Open the door — confirm and say:
“Parking brake is set, key is out.”
(Pick up the wheel block and pry bar.)
Chock the wheel on the same axle (second axle).
Say:
“This truck is equipped with an ADIS (Air Dryer Integrated System). All slack adjusters are automatic, so no manual adjustment is required.”
Say:
“Air dryer and governor are safe, secure, with no damage or air leaks.”
Explain MANUAL SLACK ADJUSTMENT:
Pull the pushrod → Observe the direction of S-cam rotation.
Fully tighten the nut in the direction in which the S-cam rotates.
Back off by ⅓ turn (20 minutes).
Recheck: ½–¾ inch of travel.
Make sure the nut is locked.
Pull → Check S-cam direction → Tighten fully → Back off ⅓ turn → Recheck ½–¾ inch → Lock
OPEN THE HOOD
START ON PASSENGER SIDE
Air line connected to brake chamber:
“Safe, secure, no audible air leak.”
Brake chamber:
“Safe, secure, no air leak.”
Pushrod travel:
“Between 1/2 and 3/4 inch.”
(Pull and hold while stating.)
MOVE TO LEFT SIDE
Compressor:
“Safe, secure, no damage, no air leak.”
Discharge line:
“Safe, secure, no damage, no air leak.”
All other air lines:
“Safe, secure, no air leak.”
Air line connected to brake chamber:
“Safe, secure, no audible air leak.”
Brake chamber:
“Safe, secure, no air leak.”
Pushrod travel:
“Between 1/2 and 3/4 inch.”
(Pull and hold while stating.)
CLOSE THE HOOD
IN CAB
(Use 3-point contact when entering and exiting the cab.)
🚛 AIR BRAKE TEST –
“START THE TRUCK” (make sure it is in neutral)
Release all parking brakes and make sure the wheels are blocked.
There are 5 tests involved with the air brake system.
1. LOW AIR WARNING:
“I will pump down now to confirm that the low air warning activates at 60 psi or above.”
👉 Say: “There, it activated just above 60 psi.” (Point your finger at the low air warning lights.)
2. COMPRESSOR REBUILD:
{Continue to fan down below 50 psi, then raise the RPM to 1000 to 1200. When the first needle reaches 50 psi, start the timer.}
Say: “I will start my timer to check the compressor rebuild time from 50 psi to 90 psi. This should not take more than 3 minutes at 1,000 to 1,200 RPM.”
👉 Say: “Now the 1st needle (secondary tank) is at 50 psi, I have started the timer. The low air warning goes off just above 60 psi. The 2nd needle (primary tank) has also reached 90 psi. There it is — 50 psi to 90 psi in 50 seconds at 1100 RPM.”
{In some air brake systems, one service reservoir may begin to fill first. When pressure reaches approximately 85 to 95 psi, the other reservoir will begin to fill. Then pressure in both service reservoirs will build to full pressure. Regardless of the type of system, pressure must build from 50 to 90 psi within three minutes.}
3. GOVERNOR CUT-OUT (COMPRESSOR UNLOADING):
Say: “Now I will continue building the pressure to confirm that the governor cuts out between 105 to 135 psi.”
👉 (When you hear the purge/sneeze)
Say: “There, the purge valve just opened, confirming governor cut-out at 125 psi.”
(PUSH IN YELLOW BUTTON IF IT POPS OUT)
4. GOVERNOR CUT-IN (COMPRESSOR LOADING):
Say: “I am pumping the pressure down to just 20 psi below maximum. (It should not go below 85 psi while pumping.) While raising the RPM, I am watching for the needles to rise.”
👉 Say: “The needles are rising, confirming governor cut-in just above 100 psi.”
5. LEAK DOWN TEST:
Build pressure to maximum psi. Turn off the engine, then turn ignition ON. Make more than a 90 psi brake application (apply full brake application — press the brake pedal all the way to the floor and HOLD). When the needles stabilize, start the timer.
Say: “I am holding more than a 90 psi brake application for 1 minute. There should be no more than 3 psi of air loss, and I am listening for any audible leaks.”
(Ensure brakes are off, open the window, and listen for air leaks.)
👉 Say: “Now it’s one minute, and the needles did not move.”
OUTSIDE BACK OF THE TRUCK
Inspect your gladhand couplers and air lines. Look for physical damage and listen for air leaks.
👉 Say: “Safe, secure, and no audible air leaks.”
UNDER THE TRUCK
Say:
“All air tanks and air lines are safe, secure, with no air leaks.”
Inspect brake assemblies on drive axles.
At each wheel:
Air line to brake chamber:
“Safe, secure, no audible air leak.”
Brake chamber:
“Safe, secure, no air leak.”
Pushrod travel:
“Between 1/2 and 3/4 inch.”
(Pull and hold.)
BACK INSIDE CAB
Apply the parking brake and remove the wheel blocks.
BRAKE RESPONSE TEST
1. PARKING BRAKE TUG TEST
Depress the clutch, shift into neutral and start the engine.
Ensure that air pressure is within the operating range.
Select a low gear and gently apply power against the parking brakes.
Say:
“Truck does not move. Parking brakes are holding properly.”
2. SERVICE BRAKE RESPONSE TEST
Release all brakes.
Move forward slowly and apply the foot brake.
Say:
“Truck stops properly, stops straight, and service brakes are working correctly.”
FINAL EXPLANATION FLOW
Chock the wheels → Explain ADIS/the wet tank and slack adjustment.
Under the hood → Check the compressor, air lines, brake chambers and slack adjusters.
Inside the cab → Perform and explain five air brake tests.
Under the vehicle → Check air tanks, air lines, brake chambers and slack adjusters.
Perform and explain the parking-brake tug test and service-brake response test.
The force that resists movement between two solid surfaces in contact with each other
How is the heat generated by air brakes dissipated?
Dissipated by the speed of the vehicle
Absorbed by the drum and dissipated into the atmosphere
Dissipated by temperature
What is the final factor that determines whether a vehicle will move?
The amount of power
The amount of traction
The amount of friction
If the speed and weight of a vehicle are doubled, by what factor must stopping power increase to stop within the same distance?
2 times
4 times
8 times
When a vehicle stops, the energy of motion is converted into what?
Heat in the brake lining and drum
Moisture in the reservoir
Traction
What is meant by reaction time?
The time the vehicle travels after the brakes are applied until it stops
The time between recognizing a hazard and applying the brakes
The time it takes for the air to move through a properly maintained air brake system
What is meant by braking distance?
The distance the vehicle travels after the brakes are applied until it stops
The distance the vehicle travels from recognizing a hazard until it stops
The actual distance the air travels through a properly maintained air brake system
8. What is the most common cause of loss of effective braking in an air brake system?
a. Loss of air pressure
Brakes out of adjustment
Overheated brakes
Brake lag is approximately four-tenths of a second in a well-maintained air brake system. What does brake lag mean?
The time it takes from the moment a hazard is recognized to the time the brake is applied
The actual time it takes for the vehicle to stop after the brakes are applied
The time required for air pressure to apply the brakes fully after the brake pedal is pressed
If a vehicle’s weight doubles, by what factor must stopping power increase to stop within the same distance?
6 times
4 times
2 times
What are the two purposes of the slack adjusters?
…………………………
…………………………….
If one set of brake shoes is poorly adjusted, how might that affect the remaining sets of brake shoes?
The brakes will automatically equalize themselves
They may carry more of the braking load, potentially causing overheating
There would be no noticeable effect on the remaining brakes
If 40 psi is exerted against a diaphragm with an area of 30 square inches, what total force could be exerted?
1,200 lbs. of force
7,200 lbs. of force
12,000 lbs. of force
What is the main cause of brake fade at high temperatures?
The air pressure becomes hot
Brakes are out of adjustment
Overheated brake drums
What are five basic components of an air brake system?
Compressor governor, air lines, reservoirs, foot valve and relay valve
Foundation brakes, foot valve, air lines, quick release valve and reservoirs
Compressor, governor, air lines, foot valve, foundation brakes and reservoir
How are most compressors lubricated?
From the engine lubricating system
From an oil supply in the compressor reservoir
From an oil supply in the compressor crankcase
What causes moisture to accumulate in an air brake system?
Air coolant leaking into the system
Air warms in the supply (wet) tank, creating moisture
Compressed air becomes hot and then cools, forming moisture
18. If the compressor discharge line breaks, what prevents a total loss of air?
The one-way check valve
The two-way check valve
The governor valve
When reservoir air pressure is at its maximum, the compressor is:
In the unloaded stage
Loaded
Not pumping air
How often should the belt on a belt-driven compressor be checked for cracks and proper adjustment?
a. Weekly
Daily
Monthly
To drain moisture from the air tanks properly, the drain cocks must be:
Left open until all air is exhausted
Opened and closed a few times fast
Cracked slightly and left
Between which two pressures must maximum reservoir pressure fall?
125 PSI and 150 PSI
50 PSI and 90 PSI
105 PSI and 135 PSI
Excessive oil accumulation in the reservoirs could indicate:
Excessive lubrication from the engine
Worn compressor piston rings
Leaking engine crankshaft oil seals
When the governor discharge valve opens, its purpose is to:
Stop the compressor from pumping air
Start the compressor pumping air
Turn on the low-air warning
At what pressure are most safety valves (pop-off or pressure-relief valves) preset to release air?
a. 135 PSI
150 PSI
175 PSI
At what pressure should the governor return the compressor to its loading (pumping) stage in a 125 psi system?
100-80 PSI
85-60 PSI
105-85 PSI
At what pressure should the LOW AIR WARNING device activate?
40-30 PSI
85-60 PSI
60-40 PSI
What must the driver do when the low-pressure warning device activates?
Apply the hand valve
Pump the foot pedal to increase the braking effort
Stop the vehicle and find the cause of the pressure drop
A foot valve is a valve that:
Will automatically adjust to braking requirements
Needs reservoir pressure to control it within 10 psi
Once applied, it continuously maintains the applied pressure
What is the maximum pressure available for a full brake application at any given time?
a. 135 PSI
Reservoir pressure
It depends on how far the foot valve is depressed
What is the fine for operating a commercial vehicle with improperly adjusted brakes?
Driver placed out of service for 10 hours
Possible fine up to $2,000
Possible fine up to $5,000
How can you tell that you are turning the slack-adjuster bolt in the correct direction when adjusting the brakes?
Always turn the adjusting bolt counterclockwise
Always turn the adjusting bolt clockwise
Turn the adjusting bolt in the direction of S-cam rotation during brake application
What are the three functions of a slack adjuster?
Connection between the pushrod and S-cam, brake adjustment and mechanical leverage
Brake adjustment, anti-compounding device and mechanical leverage
Anti-compounding device, connection between the pushrod and S-cam, and brake adjustment
An anti-lock braking system (ABS) is one that:
Modulates braking force if wheel lock-up is detected
Helps the driver retain control during heavy braking on slippery roads
Uses sensors and solenoid valves controlled by an electronic control unit (ECU)
All of the above
If the ABS light comes on while driving, you will have:
Fully functional brakes
No brakes at all
Normal braking without ABS functionality
Note:
Marks obtained: ………… Percentage: ………… Student initials: …………
Practice questions · Section 21 of 25
Test Quiz 2
TEST QUIZ 2
Signs posted before long or steep downgrades that instruct commercial-vehicle drivers to stop and inspect their brakes are:
Regulatory signs
Warning signs
Advisory signs
If one set of brake shoes is poorly adjusted, how might it affect the remaining sets?
The brakes will automatically equalize themselves
They may carry a greater share of the braking load, potentially causing overheating
There would be no noticeable effect on the remaining brakes
How are spring parking brakes held in the released position?
By spring pressure
By application pressure
By air pressure
Spring parking brakes are most useful as:
A reserve brake if the service brake fails
Mechanical parking brakes
An emergency stopping device
All of the above
Spring-brake emergency-release systems are used to:
Release air from the service brakes
Temporarily allow the use of non-essential air-operated accessories
Release the spring brakes if a disabled vehicle needs to be moved to a safe parking area
Safety-actuator parking brakes are mainly used on:
Many buses and highway coaches
Light-duty trucks
All highway tractor-trailers
7. When can brake compounding occur in some vehicles?
A full brake application is made when the spring brakes are
released
A full brake application is made when the hand valve is used
A full brake application is made when the spring brakes are applied
8. How often does a spring brake need to be caged?
At the end of your work shift
During normal operation of the brakes
Only in emergency situations
When someone makes a full service-brake application, what is the maximum pushrod travel for a manual slack adjuster?
1 inch
3/4 inch
2 inches
In the interest of safety, who is responsible for ensuring that the braking system operates correctly?
The maintenance crew
The driver
The company owner
All of the above
Proper adjustment of S-cam brakes depends on:
The size of chamber
The brake chamber pushrod
The slack adjuster
How many accepted methods are there for checking brake adjustment?
…………………………………………………………………………………
What is the maximum available stroke of a long-stroke Type 30 brake chamber?
1/2 inches
3/4 inches
3 inches
14. What is the only reliable way to confirm that your brakes are properly adjusted?
By physically checking each brake chamber for free play stroke
By feeling the response of a light brake application
By checking the pressure gauges
Braking systems with automatic slack adjusters:
Must be checked regularly to ensure correct adjustment
Do not need to be checked regularly to ensure correct adjustment
Must be checked daily for correct adjustment
If the brakes are out of adjustment, what happens to the force of the spring brake when it is applied?
Stay the same
Be greater
Be less
An automatic front-wheel limiting valve is overridden when application pressure exceeds: a. 40 psi
60 psi
80 psi
The spring-brake emergency-release system will:
Supply air to release and reapply the parking brakes if reservoir air is lost
Supply air to increase braking effort on a steep grade if main-reservoir air is lost
Supply air to stop the vehicle if main-reservoir air is lost
The maximum pressure that can be applied to a brake chamber depends on:
The size of the brake chamber
The air pressure in the reservoirs
The location of the relay valve
The automatic drain valve will:
Open momentarily each time the compressor cycles
Assist with faster brake application
Open only once every 250 km
At what pressure will the pressure-protection valve prevent further air loss from the main reservoirs?
a. 60 PSI to 90 PSI
b. 70 PSI to 80 PSI
c. 20 PSI to 45 PSI
If air is lost from one circuit of a dual-circuit air brake system, the remaining circuit will:
Activate the spring brakes
Continue to operate
Activate the trailer brakes
In a dual-circuit system, the primary circuit supplies air to:
The front brake chambers
The rear brake chambers
The main brake reservoir
In a dual-circuit system, air from both primary and secondary reservoirs is directed to:
The relay valve
The one-way check valve
The foot valve
What is the advantage of a dual-circuit system?
To reduce brake lining
To improve braking effort
To prevent total brake failure
In a dual-circuit system, which valve protects the primary circuit from air loss in the secondary circuit?
The one-way check valve
The dual-circuit foot valve
The two-way check valve
How can you identify a long-stroke brake chamber?
Size of chamber
The angle at which the chamber is mounted on the axle
A name tag or square inlet-port fitting
What does “bottoming out” mean in an air brake system?
The brake chamber hits the truck frame when applied
The foot valve hits the floor when applied
The pushrod travels to the base of the chamber
What is a bobtail proportioning valve?
It prevents rear-brake lock-up when no trailer is connected
Increases rear brake pressure
It allows the driver to make a lighter brake application
When driving, where is air pressure present in the brake chambers?
The spring-brake side
The service-brake side
Both sides (spring-brake and service-brake)
Neither side
31. When you apply the service brakes while driving, where is air pressure present in the brake chambers?
A — The spring-brake side
B — The service-brake side
C — Both sides
D — Neither side
32. After parking for the night and applying the spring brakes, where is air pressure present
in the brake chambers?
A — The spring-brake side
B — The service-brake side
C — Both sides
D — Neither side
Practice questions · Section 22 of 25
Air Brakes Review
Air brakes
Match the Air Brake Components
Match each component to its definition. Write the definition number beside the component name.
___ Quick release valve
___ Safety valve
___ Governor
___ Compressor
___ Air reservoir
___ Pressure gauge
___ Drain cocks or valves
___ Low-pressure warning
___ One-way check valve
___ Air dryer
___ Spring brakes
___ Parking control valve
Compresses air into a smaller space, increasing the force the air exerts.
Keeps the air pressure from rising to a dangerous level in the air tanks.
Mechanical brakes used for parking.
Indicates the pressure in the tanks.
Removes water vapour and oil from the air before the air reaches the first reservoir.
Warns the driver when air pressure drops below 60 psi.
Allows the brakes to release quickly. When the driver releases the foot valve, air escapes into the atmosphere.
Prevents air from flowing back into the compressor from the reservoirs.
A button (usually yellow) on the dashboard that applies and releases the spring brakes.
10. Stores compressed air for brake applications.
11. Regulates airflow to maintain the desired air pressure. When air pressure approaches its maximum, the inlet valves open.
12. Located beneath the air reservoirs; used to drain air, moisture and dirt.
Practice questions · Section 23 of 25
Air Brake Basics & Single-Unit Retest
AIR BRAKE BASICS AND SINGLE-UNIT RETEST
Circle the best answer to each question or statement.
1. How many pounds of pushrod force does a Type 30 brake chamber produce with 100 psi of air pressure in the system? a) 1,000 pounds
2,000 pounds
3,000 pounds
4,000 pounds
2. Why are air brakes used on heavy commercial vehicles instead of hydraulic brakes? They:
can apply much greater force
are much greener
require less maintenance
are much less expensive
3. Why are air brake systems less likely than hydraulic systems to fail completely? a) They can cope with small leaks
They operate under less pressure
They are less complicated
All of the above
4. Which of these is not part of an air brake chamber?
Return spring
Pushrod
Diaphragm
Two-way valve
5. On a single-unit vehicle, how many minutes may the compressor take to build reservoir pressure from 50 psi to 90 psi at a fast idle? a) 1 minute
2 minutes
3 minutes
4 minutes
6. To prevent contamination, how often should reservoirs be drained? a) Twice a day
Once a month
Once a week
Every day
7. The supply reservoir is also known as the
dry tank
wet tank
cold tank
hot tank
8. The low-air warning system must activate when pressure in any reservoir falls below a) 60 psi (414 kPa)
80 psi (552 kPa)
105 psi (723 kPa)
125 psi (862 kPa)
9. In a dual air brake system, if the primary system fails, stopping
will become impossible
distance will decrease
distance will remain the same
distance will increase
10. The parking brake control valve on the dashboard is usually which colour?
a) Brown
Red
Yellow
Green
11. What does compounding the brakes mean?
Parking brakes and service brakes applying alternately
Secondary and primary systems applying together
Parking brakes and service brakes applying together
Any of these
12. By law, when must manual and automatic slack adjusters be checked? a) Every two days
Every 1,000 km
Every day
Once a week
13. Which statement is most accurate about poorly adjusted brakes?
Poorly adjusted brakes will work normally if you increase pedal pressure
It is safe to use poorly adjusted brakes in normal operation
You will immediately notice poor adjustment
You may not notice poor adjustment during normal operation
14. Where are spring parking brakes mounted on a single-unit truck or tractor?
a) On the steering axles
On the rear axles
On the rear and steering axles
Tractors don’t have spring brakes
15. If a vehicle’s weight and speed are doubled, the stopping power required to stop within the same distance will be: a) Two times
Four times
Eight times
Ten times
16. How will going downhill affect your braking distance?
It will not affect the distance
It will increase the distance
It will shorten the distance
Traction may be lost
Practice questions · Section 24 of 25
Air Brake System — Short Answer Quiz
🚛 AIR BRAKE SYSTEM — SHORT ANSWER QUIZ
1. At what pressure does the low-air warning alarm activate? ______ p.s.i.
2. At what pressure should the safety valve activate? ______ p.s.i.
3. Between what pressures MUST the governor return the compressor to the loading stage? ______ p.s.i.
4. What is the acceptable air pressure loss during an air leak test on a single-unit? ______ p.s.i.
5. At what pressure will an automatic front-wheel limiting valve deliver 100% application pressure to the front wheels? ______ p.s.i.
6. Using the pry bar method, what should the pushrod travel be for air brakes in proper adjustment with a manual slack adjuster? ______
7. Using the applied stroke method, what should the pushrod stroke be for air brakes in proper adjustment with a manual slack adjuster? ______
8. Using the applied stroke method, what should the pushrod stroke be for air brakes in proper adjustment with an automatic slack adjuster? ______
9. How much force is delivered to the pushrod when a 100 p.s.i. application is made with a Type 30 brake chamber diaphragm? ______
10. By what percentage is front-brake braking performance reduced when a manual front-wheel limiting valve is activated? ______ %
11. What is the maximum time allowed for a compressor to build air pressure from 50 to 90 p.s.i.? ______
12. What is the maximum pushrod travel on a long-stroke Type 30 brake chamber? ______
13. Which valve can maintain the same delivery pressure even if there is a small leak? ______
14. Which valve protects against air loss if the compressor discharge line is damaged? ______
15. Which system or valve allows operation of the rear brakes if there is a primary system failure? ______
16. Which valve speeds up service-brake application to the rear wheels? ______
17. Which valve is required whenever two sources of air are used to deliver blended air to a single device or system? ______
18. What is the number one reason for an air brake system failure? ______
19. What condition will occur when the brake drums exceed their safe operating temperature? ______
20. What is the term for the condition that occurs when brake drums exceed their safe operating temperature? ______
21. What is the final factor that determines whether a vehicle will move? ______
22. How often is an operator required to inspect the belt for cracks and proper adjustment on a belt-driven compressor? ______
23. What component performs as a parking brake? ______
24. If the speed of a vehicle is doubled, how much force is required to stop it within the same distance? ______
25. What is the advantage of a dual-circuit brake system? ______
26. By what percentage does a bobtail proportioning valve reduce air pressure to the rear wheels? ______ %
27. To keep dirt out of the air lines that deliver air to the trailer, what should be attached to the holder or coupled together? ______
Yard Training Appointment —
Dear Student,
We are pleased to confirm your upcoming yard training session. This hands-on session is an important part of your air brake training and focuses on practical skills in a safe, controlled environment.
📅 Date: __________________________
🕒 Time: _________________________
📍 Location: 9985 Grace Rd, Surrey, BC V3V 3V7
🛠️ Training Focus:
During the yard session, you will receive practical instruction and guidance on:
* Air brake pre-trip inspection (practical)
* Brake adjustment awareness
* Air pressure system checks
* Safe procedures and handling in real yard conditions
👕 Dress Code & Safety:
For your safety and comfort, all students are required to wear proper yard attire, including:
* Closed-toe shoes (no slippers, sandals, or heels)
* Comfortable outdoor/work clothing suitable for physical activity
* Avoid long or loose accessories that may interfere with training.
Students not wearing appropriate footwear or clothing may not be allowed to participate in the session for safety reasons.
📌 Please Remember to Bring:
* Your valid learner’s license
* Water bottle (optional)
* Notebook and pen (optional)
⏰ Arrival Time:
Please arrive at least 10 minutes early to ensure the session starts promptly. If you are unable to attend or expect to be late, kindly inform us in 24 hour advance.
* Late cancellations or no-shows will be subject to a $50 fee.
Please go through the following link before attending the class. It contains important material that will help you better understand the session.
We look forward to seeing you at the training session. Should you have any questions, feel free to contact us at any time.
Warm regards,
Start here · Section 25 of 25
Final Pages
NANAK DRIVING SCHOOL
📞 +1 (778) 241-5791
📍 Surrey, BC
Air brake Endorsement YouTube video
Location: 9985 Grace Rd, Surrey, BC
Section 1Original wording • Offline compatible
Search the book
Search the original book text.
Notes for this section
Private to this browser. Notes are not added to or changed in the book.
Book pictures
Each picture is saved separately in the images folder. To change one later, download a replacement with the same filename and replace it in that folder before uploading your updated website. The lesson text stays exactly the same. You can keep your original pictures or backup copies in Google Drive.